|
**BRAND NEW***!!!!!!
brand new zero hours, never been run AIR COOLED HOLSET single cylinder air compressor with drive thru package (for power steering) This one puts out 8.5 CFM compared to the TF 550 at 13 CFM.... but after my scare where the compressor head ALMOST poured the entire engine coolant capacity into the engine oil pan..... I've HAD it with liquid cooled compressors..... especially used ones... So... found this one..... which should more then enough pump the air I need (hell still double my shop air compressor).... it is B-E-A-U-tiful.... love new parts old on right, new on left..... alot smaller...all the same size fittings and everything so works out great..... http://a1.sphotos.ak.fbcdn.net/hphot..._4828524_n.jpg Brand spankin new http://a8.sphotos.ak.fbcdn.net/hphot..._3792626_n.jpg Drive thru package installed http://a6.sphotos.ak.fbcdn.net/hphot..._5193447_n.jpg The LUK will bolt right up to this bad boy..... Ooopsies.... A5000 fuller plunger shattered......the cause of the rear range transmission shifting without waiting until a pass thru the neutral zone....... http://a2.sphotos.ak.fbcdn.net/hphot..._8144445_n.jpg Shes fixed now and working like a charm! The new Holset EL850 air compressor plumbed in.... http://a8.sphotos.ak.fbcdn.net/hphot..._7050146_n.jpg The air pump even pumps air ! http://a4.sphotos.ak.fbcdn.net/hphot..._1415972_n.jpg The full cycle from 0 psi to 120 psi took about 2 minutes to fill approx 13 gallons.... Mostly idle with a few bounces on the throttle..... Heres to videos of that beautiful turbo whistle (wow is the HE341 distinct and different on a 12V) and the bendix air dryer with holset compressor in action...... |
Nice! Where did you pick that up at?! Would love to have that bad boy!
|
Well.....
Its in.... permanently now..... grade 8 hardware, painted, loctite 242, all welded up.......... http://a1.sphotos.ak.fbcdn.net/hphot..._2691873_n.jpg http://a5.sphotos.ak.fbcdn.net/hphot...5_833356_n.jpg http://a5.sphotos.ak.fbcdn.net/hphot..._5033418_n.jpg http://a5.sphotos.ak.fbcdn.net/hphot...6_302806_n.jpg http://a3.sphotos.ak.fbcdn.net/hphot..._7743425_n.jpg http://a2.sphotos.ak.fbcdn.net/hphot..._2823236_n.jpg http://a2.sphotos.ak.fbcdn.net/hphot..._3054691_n.jpg The much improved over previous design panhard bar mount on axle...... this one isnt going anywhere...... http://a8.sphotos.ak.fbcdn.net/hphot..._8188888_n.jpg http://a3.sphotos.ak.fbcdn.net/hphot..._1672486_n.jpg All for now..... hydroboost comes in sometime this week..... Plans for the week are to get the top side shock mounting welded in, get the rear air bags installed, and maybe start the air solenoid valve mounting and plumbing..... Also will start mock up for pedals once I get the hydroboost mounted next week.... Moving right along..... ~M |
Where did you pick up the compressor? I'd like to swap my liqued cooled compressor out for a smaller air cooled unit too...:w2:
|
Originally Posted by 93_Fummins
(Post 753527)
Where did you pick up the compressor? I'd like to swap my liqued cooled compressor out for a smaller air cooled unit too...:w2:
|
Awsome build! Now for my only concern based on problems ive had I will now use nothing but fleetguard filters anything else ive had messed with my oil presure. I just got mine put back together (toasted thrust) when I fired it up my pressure kept fluctuating until I went to my case ih dealer and got a filter (fleetguard) after a little research I found others who have had the same problem so I try to pass it on good luck with the project ill b watchin.
|
Originally Posted by knoberman
(Post 756378)
Awsome build! Now for my only concern based on problems ive had I will now use nothing but fleetguard filters anything else ive had messed with my oil presure. I just got mine put back together (toasted thrust) when I fired it up my pressure kept fluctuating until I went to my case ih dealer and got a filter (fleetguard) after a little research I found others who have had the same problem so I try to pass it on good luck with the project ill b watchin.
Don't be fooled by the frams..... only as space savers... I fun nothing but fleetguard, and/or baldwin / CAT filters...... I replaced with NAPA Golds for engine testing.... and already have the new baldwin fuel and CAT Oil filters for the motor once it becomes a driver... |
Got ya I even had trouble with the napa gold (wix) nothing else available without goin out of town or order somewhere till I remembered case ih were fleetguard
|
New toys.....
2005 F350 6.0L hydroboost unit for the 1947...........looks real nice and clean/complete..... plus the large bore size and resevior size to boot..... http://a6.sphotos.ak.fbcdn.net/hphot...2_394924_n.jpg |
I love these updates!
|
| All times are GMT -5. The time now is 06:22 AM. |
© 2024 MH Sub I, LLC dba Internet Brands